Temperature Transducer with Bacnet and Modbus RS485
€16.78 - €30.91
Duct mount temperature only transducer, Bacnet/Modbus over RS485, 0-10v 4-20ma output signal
Product Highlights:
-High precision sensor accurate to 2% humidity over the entire temperature range.
-Duct mount style is suitable for typical HVAC and agricultural applications
-Field selectable span for the temperature range
-100% field changeable Temp/Hum module, no tools or calibration needed.
-Jumper select the output signal: 4~20mA or 0-10V
-BACnet MS/TP and Modbus RTU protocols over RS485.
-Enthalpy and dew point are available over the RS485 link
Available Options:
Duct temperature transmitter is applicable to all kinds of building automation, environment monitoring, HVAC systems. Product appearance is simple, direct connection terminals, convenient installation.Products use high performance embedded microprocessor, and high-precision sensors to meet all kinds of high precision,high stability of the temperature measurement requirements , and variety needs of different environments.Duct temperature sensor / transmitter has current,voltage, 485 output signal to select, using 485 serial port out put and Modbus communication protocol. It is commonly used in HVAC, electrical plant,environment monitoring,dynamic environment monitoring, agricultural environmental monitoring, meteorological environmental monitoring,environmental monitoring of biological pharmacy, airport,subway stations, hotel,museum,stadium, etc.
Dimension
Wiring Diagram
Part Num Scheme
| Weight | 0.1 kg |
|---|---|
| Module type | Temperature, Water Temperature Sensor |
| Probe Length | 2 inch, 3 inch, 4 inch, 6 inch |
Related Products
-
Thermowells
€4.86 - €7.51Availability: In stockOut of stock
These thermowells are designed for mounting temperature sensors in pipes and tanks.The thermowells are designed to handle this stress while providing good thermal contact with the fluid.They also provide isolation, if the sensor needs to be serviced the system can remain in operation without having to drain the lines. The thermowells are machined from a single piece of bar stock, there are no welds as found on competing products.
-
Outdoor Air Temperature Sensor, Overmolded
€4.42 - €5.30Availability: In stockOut of stock
The temperature sensor is designed to measure outdoor air temperature in typical HVAC applications. Mounting is quick and easy using two screws and no electrical box. The thermistor is a well sealed stainless steel probe which is then inserted into a hard rubber PVC radiation shield. The cable is two meters long which allows terminating inside the building in an electrical enclosure or with flying leads. The cable can exit directly behind the probe and into the building through a hole, or it can exit vertically and run down the wall. A foam backing seals the hole in the wall if there is one and also serves to thermally insulate the probe from the wall. The probe is filled with thermal grease for quick response.
-
1K PT Temperature Sensors
€2.47 - €8.30Availability: In stockOut of stock
The 1K Platinum temperature sensors for building automation, agricultural and light industrial duty applications.
-
WTS6-I: Strap-On Insert Temperature Sensor
€4.42Availability: In stockOut of stock
The strap-on Insert sensor consists of a stainless steel sheath temperature sensor, thermal conducting compound, and an adjustable pipe bracket accessory. The stainless steel sheath temperature sensor is suitable for direct application to pipe surfaces for chilled or hot water measurement.
-
High temperature over molded floor heating sensor
€4.86Availability: In stockOut of stock
High temperature over molded floor heating sensor,4.5m cable length,6.0mm diameter pipe,10k Type2 thermistor.
-
Bacnet Room Setpoint & Temp Display
€33.55Availability: In stockOut of stock
Bacnet Room Setpoint & Temp Display can be used in environment monitoring and controlling in industrial,commercial and other buildings,Modbus RS485/Bacnet MS/TP for direct digital reading on all models.
-
Duct Temperature Sensor – Flange Mount
€4.42 - €7.06Availability: In stockOut of stock
This sensor is used to measure the supply and return temperature in HVAC system. The flange mount design makes it easy to install the sensor in tight quarters. There are several sensor elements to choose from which guarantee compatibility with all popular DDC systems. The probe in the photo is our standard model which is always in stock, it has a 8″ probe and a 120″ cable, and employs either a precision thermistor or platinum film sensor, so field calibration is not required. The 10ft(3m) cable is “Plenum Rated”.
-
WTS Series Water Temperature Sensor
€4.42 - €11.92Availability: In stockOut of stock
This sensor is used to measure water temperature of heated or chilled water and other liquids in mechanical systems. The sensor is called an immersion type where the sensor is mounted in a brass or stainless steel thermowell which allows the probe to be removed from the pipe without draining the system and protects the probe.There are four thermistor based models, and one RTD version to provide compatibility with the majority of DDC systems.
-
WTS5: Strap-on Water Temperature Sensor
€6.18 - €7.06Availability: In stockOut of stock
This sensor is used to measure water temperature of heated or chilled water and other liquids found in the various mechanical systems of building. The sensor is especially intended for strapping to the outside of a pipe when there is no opportunity to install a well such as in a retrofit or additions to an existing system.The strap on probe is useful in applications such as monitoring batteries, transformers, generators, and generally any place where a complete assembly can not be mounted,Ice rink slabs and soil temperature are other applications.
