Bacnet Room Setpoint & Temp Display
CAD $48.98
10 in stock
Bacnet Room Setpoint & Temp Display can be used in environment monitoring and controlling in industrial,commercial and other buildings,Modbus RS485/Bacnet MS/TP for direct digital reading on all models.
Product Highlights:
- The output signals and RS485 are hardened up for overvoltage and power supply crossed over.
- Display in degrees Fahrenheit or Celsius(connection to Bacnet).
- The LCD is a bitmap so we can show network connectivity.
- You can show a user setpoint so you can use it as a room /setpoint display.
- Modbus RS485/Bacnet MS/TP for direct digital reading on all models.
Weight | 0.1 kg |
---|
Related Products
-
1K PT Temperature Sensors
CAD $3.61 – $12.12Availability: In stockOut of stock
The 1K Platinum temperature sensors for building automation, agricultural and light industrial duty applications.
-
Thermowells
CAD $7.09 – $10.96Availability: In stockOut of stock
These thermowells are designed for mounting temperature sensors in pipes and tanks.The thermowells are designed to handle this stress while providing good thermal contact with the fluid.They also provide isolation, if the sensor needs to be serviced the system can remain in operation without having to drain the lines. The thermowells are machined from a single piece of bar stock, there are no welds as found on competing products.
-
High temperature over molded floor heating sensor
CAD $7.09Availability: In stockOut of stock
High temperature over molded floor heating sensor,4.5m cable length,6.0mm diameter pipe,10k Type2 thermistor.
-
Outdoor Air Temperature Sensor
CAD $9.02 – $10.31Availability: In stockOut of stock
This sensor is used to measure the outside air temperature to allow the DDC system to coordinate the mechanical systems with actual building load conditions, enabling such strategies as free cooling, optimum start/stop, and supply temperature reset. The housing is made from PVC and stainless steel fittings which shield the probe from direct sunlight. There are three thermistor based models, and one RTD version to provide compatibility with the majority of DDC systems.
-
Outdoor Air Temperature Sensor, Overmolded
CAD $6.45 – $7.73Availability: In stockOut of stock
The temperature sensor is designed to measure outdoor air temperature in typical HVAC applications. Mounting is quick and easy using two screws and no electrical box. The thermistor is a well sealed stainless steel probe which is then inserted into a hard rubber PVC radiation shield. The cable is two meters long which allows terminating inside the building in an electrical enclosure or with flying leads. The cable can exit directly behind the probe and into the building through a hole, or it can exit vertically and run down the wall. A foam backing seals the hole in the wall if there is one and also serves to thermally insulate the probe from the wall. The probe is filled with thermal grease for quick response.
-
WTS6-I: Strap-On Insert Temperature Sensor
CAD $6.45Availability: In stockOut of stock
The strap-on Insert sensor consists of a stainless steel sheath temperature sensor, thermal conducting compound, and an adjustable pipe bracket accessory. The stainless steel sheath temperature sensor is suitable for direct application to pipe surfaces for chilled or hot water measurement.
-
Temperature Transducer with Bacnet and Modbus RS485
CAD $24.49 – $34.80Availability: In stockOut of stock
Duct mount temperature only transducer, Bacnet/Modbus over RS485, 0-10v 4-20ma output signal
-
Duct Averaging Temperature Sensors
CAD $4.51 – $78.63Availability: In stockOut of stock
Temperature is detected by a range of thermistors. The
special mechanical construction the sensor is able to detect
temperature throughout its entire length. -
WTS Series Water Temperature Sensor
CAD $6.45 – $17.40Availability: In stockOut of stock
This sensor is used to measure water temperature of heated or chilled water and other liquids in mechanical systems. The sensor is called an immersion type where the sensor is mounted in a brass or stainless steel thermowell which allows the probe to be removed from the pipe without draining the system and protects the probe.There are four thermistor based models, and one RTD version to provide compatibility with the majority of DDC systems.