WTS Series Water Temperature Sensor
$5.00 - $13.50
This sensor is used to measure water temperature of heated or chilled water and other liquids in mechanical systems. The sensor is called an immersion type where the sensor is mounted in a brass or stainless steel thermowell which allows the probe to be removed from the pipe without draining the system and protects the probe.There are four thermistor based models, and one RTD version to provide compatibility with the majority of DDC systems.
Product Highlights:
- High-accuracy
- Easy Installation
- Highly portable and reusable
- Four thermistor based models
- Probe Material: Stainless Steel 304, 1mm thick wall
Available Options:
Immersion type water temperature sensor
Installation:
Water temperature sensors can be located at any suitable location in the system.A NPT female pipe fitting is welded into the pipe.These fittings are usually supplied and installed by the piping trade under direction of the controls trade.The fitting can be welded on any suitable section of pipe, in either a horizontal or vertical pipe section.Choose an orientation where any condensation will not drip into the electrical box, such as the top of a horizontal pipe section.Before threading the sensor into the well, deposit some thermal paste in the bottom of the well to improve heat conduction between the metal parts.The sensor is wired with two conductor 18 ga, unshielded twisted pair.
Part Number Scheme:
| Weight | N/A |
|---|---|
| Enclosure | Metal 11-10 electrical box, metal outdoor electrical box, watertight plastic box |
| Probe Length | 2 inch, 4 inch, 6 inch |
| Temperature Curve | 100PT, 10K Type 2, 10K Type 3, 1K PT |
Related Products
-
Outdoor Air Temperature Sensor, Overmolded
$5.00 - $6.00Availability: In stockOut of stock
The temperature sensor is designed to measure outdoor air temperature in typical HVAC applications. Mounting is quick and easy using two screws and no electrical box. The thermistor is a well sealed stainless steel probe which is then inserted into a hard rubber PVC radiation shield. The cable is two meters long which allows terminating inside the building in an electrical enclosure or with flying leads. The cable can exit directly behind the probe and into the building through a hole, or it can exit vertically and run down the wall. A foam backing seals the hole in the wall if there is one and also serves to thermally insulate the probe from the wall. The probe is filled with thermal grease for quick response.
-
Thermowells
$5.50 - $8.50Availability: In stockOut of stock
These thermowells are designed for mounting temperature sensors in pipes and tanks.The thermowells are designed to handle this stress while providing good thermal contact with the fluid.They also provide isolation, if the sensor needs to be serviced the system can remain in operation without having to drain the lines. The thermowells are machined from a single piece of bar stock, there are no welds as found on competing products.
-
Duct Averaging Temperature Sensor
$39.00 - $63.00Availability: In stockOut of stock
The sensor measures temperature in stratified air such as the mixing sections of air handlers. The sensor has a standard 10k type 2 temperature-resistance curve compatible with all major control systems.
-
WTS6-I: Strap-On Insert Temperature Sensor
$5.00Availability: In stockOut of stock
The strap-on Insert sensor consists of a stainless steel sheath temperature sensor, thermal conducting compound, and an adjustable pipe bracket accessory. The stainless steel sheath temperature sensor is suitable for direct application to pipe surfaces for chilled or hot water measurement.
-
Temperature Transducer with Bacnet and Modbus RS485
$19.00 - $27.00Availability: In stockOut of stock
Duct mount temperature only transducer, Bacnet/Modbus over RS485, 0-10v 4-20ma output signal
-
Boiler stack temperature sensor and thermowell, 1k Pt
$28.00 - $31.00Availability: In stockOut of stock
The Boiler stack temperature sensor and thermowell are designed to monitor the temperature of boiler stacks, steam lines and other applications where the temperature is above the operating range of typical HVAC thermistor type sensors. Maximum operating temperature of 300 Deg C (570 DegF).
-
RTS Wall and Bead Sensors
$1.00 - $3.50Availability: In stockOut of stock
The room sensors are used to provide reliable, accurate temperature readings in surface-mount room environments, Energy Management Control Systems, compatible with all the leading control systems.They feature a standard plastic ventilated enclosure.
-
Outdoor Air Temperature Sensor
$7.00 - $8.00Availability: In stockOut of stock
This sensor is used to measure the outside air temperature to allow the DDC system to coordinate the mechanical systems with actual building load conditions, enabling such strategies as free cooling, optimum start/stop, and supply temperature reset. The housing is made from PVC and stainless steel fittings which shield the probe from direct sunlight. There are three thermistor based models, and one RTD version to provide compatibility with the majority of DDC systems.
-
WTS6-E: Strap-On External Temperature Sensor
$5.00 - $6.00Availability: In stockOut of stock
The strap-on temperature sensor is used for sensing the temperature of pipework in heating, ventilation and air conditioning systems.
